Concentration fluctuation caused by reaction-diffusion coupling near catalytic active sites

The coupling of reaction and diffusion between neighboring active sites in the catalyst pore leads to the spatiotemporal fluctuation in component concentration, which is very important to catalyst performance and hence its optimal design. Molecular dynamics simulation with hard-sphere and pseudo-particle modeling has previously revealed the non-stochastic concentration fluctuation of the reactant/product near isolated active site due to such coupling, using a simple model reaction of A → B in 2D pores. The topic is further developed in this work by studying the concentration fluctuation due to such coupling between neighboring active sites in 3D pores. Two 3D pore models containing an isolated active site and two adjacent active sites were constructed, respectively. For the isolated site, the concentration fluctuation intensifies for larger pores, but the product yield decreases, and for a given pore size, the product yield reaches a peak at a certain reactant concentration. For two neighboring sites, their distance (d) is found to have little effect on the reaction, but significant to the diffusion. For the same reaction competing at both sites, larger d leads to more efficient diffusion and better overall performance. However, for sequential reactions at the two sites, higher overall performance presents at a smaller d. The results should be helpful to the catalyst design and reaction control in the relevant processes.     

Fluid sloshing thermo-mechanical characteristic in a cryogenic fuel storage tank under different gravity acceleration levels

Fluid sloshing usually causes serious safety issues on the dynamic stability and propellant thermal management during the powered-flight phase of launch vehicle. With the wide using of cryogenic propellants, the coupled thermo-mechanical performance during fluid sloshing becomes more prominent. In the present study, one numerical model is established to simulate fluid sloshing by using the VOF method coupled with the mesh motion treatment. The phase change occurring within the tank is considered. Both the experimental validation and mesh sensitivity analysis are made. It shows that present numerical model is acceptable. Based on the developed numerical model, the effect of different super gravity accelerations on fluid sloshing hydrodynamic characteristic is numerically researched. The fluid pressure variation, the sloshing force and sloshing moment, the interface dynamic response and the interface shape variation are investigated, respectively. It shows that the gravity acceleration has caused obvious influences on fluid sloshing characteristic. When the gravity acceleration is higher than 4g₀, fluid sloshing becomes more obvious and must be paid enough attention. With some valuable conclusions obtained, the present work is of great significance for in-depth understanding of fluid sloshing mechanism.     

Annealing temperature-dependent structural and electrical properties of (Ta2O5)1-x - (TiO2)x thin films,x ≤ 0.11

(Ta₂O₅)_1-x- (TiO₂)_x (TTO_x) thin films, with x = 0, 0.03, 0.06, 0.08, and 0.11, were deposited using magnetron direct current (DC) sputtering method onto the P/boron-silicon (1 0 0) substrates by varying areas of Tantalum and Titanium metallic targets, in oxygen environment at ambient temperature. The as-deposited thin films were annealed at temperatures ranging from 500 to 800 °C. Generally, the formation of the Ta₂O₅ structure was observed from the X-ray diffraction measurements of the annealed films. The capacitance of prepared metal– oxide– semiconductor (MOS) structures of Ag/TTO_x/p-Si was measured at 1 MHz. The dielectric constant of the deposited films was observed altering with varying composition and annealing temperature, showing the highest value 71, at 1 MHz, for the TTO_x films, x = 0.06, annealed at 700 °C. With increasing annealing temperature, from 700 to 800 °C, the leakage current density was observed, generally decreasing, from 10^?5 to 10^?8 A cm^?2, for the prepared compositions. Among the prepared compositions, films with x = 0.06, annealed at 800 °C, having the observed value of dielectric constant 48, at 1 MHz; and the leakage current density 2.7 × 10^?8 A cm^?2, at the electric field of 3.5 × 10⁵ V cm^?1, show preferred potential as a dielectric for high-density silicon memory devices.     

Optical design of the Lyman alpha based beam emission spectroscopy(LAB)diagnostic on the HL-2A tokamak

In this article, we present the optical design of a novel diagnostic on the HL-2 A tokamak, i.e. the20-channel edge Lyman-alpha beam emission spectroscopy, which is a promising solution for edge density turbulence research on tokamaks, as it offers the possibility of density fluctuation measurement with a 3.3 mm spatial resolution while maintains a high temporal resolution of1 μs. The optical path, including the reflective collection optics, the high-dispersion spectrometer, and the linear detector array, is carefully optimized to obtain a good image quality and a high throughput. The maximum root mean square radius of the collection optics is 64 μm.The detected photon flux is estimated to be about 10~(11) photons/s/channel.     

基于混合模式快速电荷平衡的神经刺激器

设计实现了一种可用于脊髓神经刺激器的多通道大电流神经刺激器。提出将电极短接和插入短电流脉冲相结合的混合模式,在大电流下,能更加快速地实现电荷平衡。电路设计上,将ADC动态比较器的回踢噪声消除技术应用于神经刺激器,使得动态比较器在输入压差较小时能够输出正确的比较结果,从而将电极上残留电压保持在更安全的范围内。基于CSMC 0.25 μm BCD工艺进行设计与仿真,结果表明,在单向且最大刺激电流为4 mA、刺激脉宽为60 μs、刺激周期为750 μs的条件下,该15 V、16路神经刺激器能实现±50 mV安全电压的有源电荷平衡。     

瞬变电磁井间勘探的全空间几何因子

井间是剩余油的主要分布区域,为探测井间剩余油,提高采收率,提出了基于全空间几何因子的瞬变电磁井间勘探方法。在本井使用线圈发射、邻井使用线圈接收,根据瞬变电磁场理论,在阶跃信号的激励下发射线圈在地层中激发出沿圆周方向的闭合瞬变电场,该电场在导电地层中产生与地层电导率呈正比的涡流。由Doll地层环模型可知,地层中的涡流在空间任意点激发得到与地层电导率成正比的二次场响应信号(有用信号),并可表示为空间各点电导率的加权平均值,其权重即为井间瞬变电磁勘探的全空间几何因子;全空间几何因子集中分布在发射线圈和接收线圈附近,其它区域分布较少,在发射线圈和接收线圈两侧呈现不同的极性;对瞬变电磁响应与地层电导率、井间距和源距的变化规律研究可知,瞬变电磁井间勘探有用信号随着地层电导率的增大而增大,随着井间距的增加单调减小,在发射线圈和接收线圈处于同一深度时该响应信号幅度最大。     

纵轴式掘进机截割头载荷影响因素的仿真分析

针对现有掘进机截割头载荷特性研究方法采用单一影响因素不能全面反映截割头载荷及其波动变化规律的问题,通过分析截割头瞬时载荷,确定了纵轴式掘进机在水平截割工况下截割头载荷的主要影响因素有截割岩石特性、截割头掏槽深度、截割头吃刀深度、截割头转速和截割臂摆速。针对某纵轴式掘进机水平截割工况,采用Matlab对影响截割头载荷的多种因素进行仿真分析,得到了各向载荷及其波动随各因素的变化规律:截割头载荷随着岩壁普氏系数的增大而增加,其中横向阻力增加尤为明显,横向阻力波动程度高于其他方向载荷,且随着岩壁普氏系数的增大呈减小趋势;随着截割头掏槽深度的增加,截割头各向载荷近似呈线性增加,其中升力增加幅度最大,各向载荷波动则随着截割头掏槽深度的增大而减小;随着吃刀深度的增加,截割头载荷总体呈增大趋势,载荷波动程度则随之减小;在截割头转速一定的情况下,截割头载荷均随着截割臂摆速的增加而增大,在同一摆速下,截割头载荷随着截割头转速的减小而增大,横向阻力波动明显高于升力和推进阻力波动,横向阻力和推进阻力波动按截割头载荷规律变化,升力波动则与之相反。截割头载荷波动变化规律与截割头载荷变化规律不尽一致,有时甚至相互冲突。因此,掘进机作业过程中应合理选择截割头掏槽深度、吃刀深度等操作参数和截割头转速、截割臂摆速等运动参数,使各参数相互匹配,以减小掘进机振动,延长使用寿命。     

浅谈不同给液方式在铜电解车间的应用

不同给液方式对铜电解过程中有重要的影响,不同的循环方式会影响槽内温度分布、电解液成分及阳极泥沉降等,因此,根据铜电解生产不同情况的需要,分析对比了多种给液方式在贵冶电解车间的应用,总结了这几种给液方式的优缺点和适用条件。     

Design and characteristics of a new type laminar plasma torch for materials processing

Laminar plasma jet(LPJ) generated by laminar plasma torch(LPT) has a favorable temperature and velocity distribution. Thus, it is superior to the turbulent plasma jet in material processing.However, most of the reported LPTs usually operate at a relatively low output power with a relatively low arc voltage and thermal efficiency, which limits its capabilities. In this context, this paper attempts to design a new type of high-power LPT with a relatively low arc current and a high thermal efficiency. In the first section, the design principle of the main components is studied and discussed in detail, and a new high-power LPT is proposed. Then, the experimental characteristics of the proposed high-power LPT are examined. Experimental results reveal the following characteristics of the proposed LPT.(1) The max jet length of the proposed LPT reaches at 540 mm.(2) Its mean arc voltage is higher than 290 V when the LPT works with arc currents lower than 200 A, leading to an output power greater than 50 kW.(3) The mean thermal efficiency is higher than 50%. Lastly, the proposed LPT has been applied to spheroidize the aluminum oxide powers. The experiment results for the production of spherical powders show that the proposed LPT has a good characteristic for material processing.     

Effects of stray AC on corrosion of 3-layer polyethylene coated X70 pipeline steel and cathodic delamination of coating with defects in 3.5 wt-% NaCl solution

In this work, the effects of stray alternating current (AC) on the corrosion of coated X70 pipeline steel and the delamination of 3-layer polyethylene (3PE) coatings with defects were investigated using COMSOL Multiphysics simulation, electrochemical impedance spectroscopy and three-dimensional (3D) digital microscope techniques. The results showed that under the same level of AC interference, pits with deeper maximum pit depth were observed at the smaller defect areas than those at larger defect areas. It was consistent with the simulation results that a greater corrosion current density was accompanied on samples with smaller defects. According to 3D digital images, the larger delamination of 3PE coatings was found on samples with smaller defects. With the increase of current density, the impedance of samples with small defects decreased, while that of samples with large defects increased. Additionally, with the same defect size, the maximum pit depth became deeper and the corrosion was more severe.